#Molex connector for pinball 9 pin install
#Molex connector for pinball 9 pin serial
#Molex connector for pinball 9 pin drivers
#Molex connector for pinball 9 pin software

Williams D-8359 5773-09474-01 Arcade Linear Power supplies used on games such as Defender, early Stargate, Pinballs or any other game with this power supply. Both NEW heat sink transistors 2N3055 and upgraded 2N6059.New IC1 and IC2 Voltage Regulator Chips DIP-14 (2 pieces).All new slow blow fuses for F1, F2, F3, F4, F5 (5 pieces).Molex Trifurcon crimp pins (50 pieces 18-20 gauge).156 connector housings for wire harness that connect to 4J1, 4J2, 4J3 (3 pieces) Molex PCB header pins for 4J1, 4J2, 4J3 (2 pieces 24 pin breakaway headers).NO CAPACITORS INCLUDED IN THIS KIT BUT THEY CAN BE PURCHASED IN THE D8359 CAP KIT FROM THE LINK BELOW. It's also much easier to browse his selection to find the most appropriate parts.Williams D-8359 Mega Deluxe Power Supply Rebuild Kit is a completely inclusive kit with components and all connectors/headers and almost every part is rated much higher then the original its replacing. His prices are comparable (and sometimes lower) than Digikey and Mouser. Great Plains Electronics primarily supports pinball hobbyists.Molex connectors/pins/housings: Great Plains Electronics*, Digikey, Mouser

You can always cut them down if you ever need smaller ones.

Buy a few extra housings with the largest number of pins you foresee needing.

Using keying plugs in your connector housings will help you avoid accidentally plugging housings onto the wrong headers. The board connector's use different key patterns to differentiate the various types of connections (ie. Not only do they hold the header in place, but they also make it obvious which way to plug on the header. Crimping a lot of pins with a hard to use tool isn't fun!

Note: Not all connectors are used on all boards.

These boards use the following molex connectors:

Note: If using this board to drive a lamp/led matrix, connect J11 to the cathode side of your LED matrix (or the return side of your lamp matrix).

Note: If using this board to drive a lamp/led matrix, leave J4 unconnected.

Note: If using this board to drive a lamp/led matrix, connect J7 to the anode side of your LED matrix (or the input power side of your lamp matrix).

Note: If using this board to drive a lamp/led matrix, leave J3 unconnected.

Connect your voltage source (5V-20V) to the Bank A Power Input connector (J5).

Ensure F2 has a properly rated fuse for your application.

J11 connects to the Bank B transistors, which complete the path to ground when activated. Connect each of your devices to the desired pin in J11.Use the Bank B Power Output connector (J4) to supply power to the devices you want to control with this board/bank.Connect your voltage source (5V-80V) to the Bank B Power Input connector (J6).Ensure F1 has a properly rated fuse for your application.J7 connects to the Bank A transistors, which complete the path to ground when activated. Connect each of your devices to the desired pin in J7.Use the Bank A Power Output connector (J3) to supply power to the devices you want to control with this board/bank.

Connect your voltage source (5V-80V) to the Bank A Power Input connector (J5).Refer to the P-ROC FPGA specs for more details on the command format.

#Molex connector for pinball 9 pin software

When using a P-ROC, boards with addresses greater than 7 must be accessed directly by software by writing the appropriate data to Module 3, Address 0xC00.

#Molex connector for pinball 9 pin drivers

Note, P-ROC drivers can be configured into driver groups for the first 8 board addresses (0-7).

Dipswitches 4:1 map to board address 3:0.

Set the address (dipswitches 4 through 1) to a unique address.

#Molex connector for pinball 9 pin serial

Connect the the Serial Output connector (J10) to next board's Serial Input connector (J9).

Connect the the Serial Input connector (J9) to previous board's Serial Ouptut connector (J10) (unless this is a master-combo board).

Note - These instructions also apply to the master portion of master-combo boards.

Connect the Master board's Serial Output connector (J10) to next board's Serial Input connector (J9).

Simply using a current limiting resistor is NOT sufficient. If you are using a 5V controller, be sure to level translate the signal before it reaches the Master board.

Note, the Master board's data input pin (pin 1 on the ribbon cable header) is a 3.3V input.

If you're not using a P-ROC, connect your controller's serial data pin to pin 1 on the Master board's ribbon cable header and at least one ground pin from your controller to an even numbered pin on ribbon cable header.

Master board J8 connects to P-ROC J34 header via the 16-pin ribbon cable that came with the board.

#Molex connector for pinball 9 pin install

Install the Master near the P-ROC (or other controller).